| Author |
Repair GDFS |
Malex
Joined: Jan 03, 2008
Posts: 77
From: Minsk, Belarus
PM, WWW
|
I used dcu60 cable |
|
|
alfath
Joined: Sep 13, 2007
Posts: 74
From: lost in space...
PM |
try to charge ur battery outside ur phone using any charger untill full and then try to reconnect...
_________________
K800i black--> K810 R8BA+hpm 70+1gb m2 sandisk+lot off patches.
[ This Message was edited by: alfath on 2008-05-25 19:44 ] |
bryanjay420
Joined: Jan 18, 2008
Posts: 273
From: Pinas
PM |
did you install usb drivers first???if it doesnt have red light blinking in infrared you dont have to hold 2+5...and in flashing you must hold c...
|no  phone to mod| |i my k800| |
opexblue
Joined: Jan 18, 2006
Posts: 226
From: Manado, North Celebes, INA.
PM |
OK, this what I've tried.
I've backup the original GDFS
All driver needed is installed.
Batt is fully charge using my friend's phone (W830).
Try to flash using SEtool2 lite (hold c while connect) ==> not detected
Try to flash and write GDFS using SEtool2 lite (hold 2+5 while connect) ==> got this log :
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
Flash ID check:2019
Flash props sent ok
OTP LOCKED:1 CID:51 PAF:1 IMEI:35471601230700 CERT:N/A
phoneid error 1
Error during phone id.
Elapsed:18 secs.
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:35471601230700 CERT:N/A
phoneid error 1
Phone info read error !
Elapsed:36 secs.
Try to flash using XS++ 3.1 (hold c while connect) ==> not detected
Try to flash using XS++ 3.1 (hold 2+5 while connect) ==> got this log :
00:27:39| XS++ v3.1 (Darwin) Ready !
00:27:39| Executed on Microsoft Windows XP
00:27:45|
00:27:45| Attempting to open the interface...
00:27:45|
00:27:45| TURN OFF PHONE!
00:27:45| Hold 'C' button on phone and connect phone NOW.
00:27:45| You have 30 seconds...
00:27:45|
00:28:04| Baseband ID: 9900
00:28:04| Protocol Version: 3.1
00:29:56| Cannot open ŒýC
00:29:56| Sendinging shutdown signal to phone...
00:29:58| Shutting down..
Still no luck. I think I'm gonna give a rest for a day or two then try it again... 
I'll post the result...
Meanwhile all suggestion is very much accepted.
Thanks for your help guys..!! 
You are all wonderful...
[ This Message was edited by: opexblue on 2008-05-28 12:44 ]
[ This Message was edited by: opexblue on 2008-05-28 12:50 ] |
Malex
Joined: Jan 03, 2008
Posts: 77
From: Minsk, Belarus
PM, WWW
|
You're welcome 
Try to flash your main first holding 2+5 |
opexblue
Joined: Jan 18, 2006
Posts: 226
From: Manado, North Celebes, INA.
PM |
Updated.
I've try it 5 times, now I'm doom.
SEtool2 lite & XS++ doesn't detect my phone at all (Holding 'C' and '2+5'). It seems I have to take it to SE Service Center.
[ This Message was edited by: opexblue on 2008-05-31 05:10 ] |
|
|
Posted: 2008-05-24 22:59
phone to mod| |i 
