| Author |
HELP ME with my V800 |
amnesia
Joined: Jan 15, 2004
Posts: > 500
From: Doha, London, Tokyo, Shanghai
PM, WWW
|
Since nobody responds as quick to the other threads I've posted this here.
I'm F***ing pissed.
I took the Marques advice and tried to use Davinci to flash my V800.
Now before you go ah he's gone and damaged the phone himself here me out.
I did nothing except follow the instructions on the site.
I did a Check CID and it said my phone was damaged. BEFORE I EVEN DID ANYTHING!
Now when i try to switch it on it just switches on the LEDS in a dimmed mode.
WTF!
I tried a recovery flash.
Worked fine until it gets to Finalization and then it says ERROR.
*sighs*
I just got this phone, and I'm not on a contract so I can't go to Voda...
|
|
|
gbrooks3
Joined: Jun 02, 2003
Posts: > 500
From: OTP RED CID36
PM, WWW
|
Dont be angry and dont worry either. You cant damage a phone beyond repair with these things.
What cable do you have? |
amnesia
Joined: Jan 15, 2004
Posts: > 500
From: Doha, London, Tokyo, Shanghai
PM, WWW
|
i'm ussing the DSS-25.
The Davinci Team Manual said that it's possible.
Problem is that I can't charge the battery so once it's empty... I guess I can't do anything more myself.
_________________
Oxygen Inc
[ This Message was edited by: amnesia on 2005-05-06 14:46 ] |
gbrooks3
Joined: Jun 02, 2003
Posts: > 500
From: OTP RED CID36
PM, WWW
|
Yes it is but unfortunatly davinci use a very crude method to recover the V800 i.e. replace EROM where recovery certificate was left.......If you phone powers on now - flash recovery files again then flash normal R1Y main and FS files. |
amnesia
Joined: Jan 15, 2004
Posts: > 500
From: Doha, London, Tokyo, Shanghai
PM, WWW
|
no you see when I try to power it on, the leds around the camera light up only.
Nothing else switches on.
I'm trying to do a recovery flash now at a low speed.
|
gbrooks3
Joined: Jun 02, 2003
Posts: > 500
From: OTP RED CID36
PM, WWW
|
V800 has marita chipset and when detected should be flashed at 460800 baud but 115200 is fine......... |
amnesia
Joined: Jan 15, 2004
Posts: > 500
From: Doha, London, Tokyo, Shanghai
PM, WWW
|
i didn't know that. the site said to use 921600.
I'm flashing at 57600 now just to be safe.
I cant stop it now can I?
(i'm checking this thread every few minutes)
|
gbrooks3
Joined: Jun 02, 2003
Posts: > 500
From: OTP RED CID36
PM, WWW
|
No its fine. But flashing a V800 at 921600 is not gonna happen as far as i know. As soon as the recovery flash finishes - just flash the normal main and FS files with default finalization. |
amnesia
Joined: Jan 15, 2004
Posts: > 500
From: Doha, London, Tokyo, Shanghai
PM, WWW
|
while it's finishing, can you fill me in on a few things.
When it finishes, I'll take it out of the dock, remove the battery and then try to switch it on.
If it works great I'll flash again after a charge, if not, what should I do?
|
gbrooks3
Joined: Jun 02, 2003
Posts: > 500
From: OTP RED CID36
PM, WWW
|
If not then we shall try something different. Do not fear, you can only kill a phone with a hammer, brick, car, cliff edge etc etc
I thint that maybe your phone had been updated at some point with CID36 files. And when these programs detect CID36 bad things can happen  |
amnesia
Joined: Jan 15, 2004
Posts: > 500
From: Doha, London, Tokyo, Shanghai
PM, WWW
|
i've only had the phone for 2 days.
Before that it I bought it off of Roulf, who said it was new and only switched on to be unlocked.
I'm not familiar with CID #'s or Jargon, this is the first unofficial flash I've attempted...
Guess we'll wait and see.
|
gbrooks3
Joined: Jun 02, 2003
Posts: > 500
From: OTP RED CID36
PM, WWW
|
Whats unoffical about it? You are using SEMC copyrighted files and you are using an EMMAII connection to finalize the phone - exactly as any service centre |
amnesia
Joined: Jan 15, 2004
Posts: > 500
From: Doha, London, Tokyo, Shanghai
PM, WWW
|
i got so close to the end of finalization and then got this
Wait while process will be finished!
V800 recognized!
CsLoader Accepted Ok!
System Initialization. Please Wait...
Getting data from server...
Connection ok! Data recieving...
Sign 1 ok.
Sign 2 ok.
CsLoader Unlocked!
Error! Block not accepted
Error! Block not accepted
Error! Block not accepted
Error! Block not accepted
Error! Block not accepted
oh wait i forgot to add
Error! Block not accepted
Error! Block not accepted
Error! Block not accepted
Error! Block not accepted
Error! Block not accepted
Error! Block not accepted
Error! Block not accepted
Error! Block not accepted
Error! Block not accepted
Error! Block not accepted
Error! Block not accepted
Error! Block not accepted
Error! Block not accepted
Error! Block not accepted
Error! Block not accepted
Error! Block not accepted
Error! Block not accepted
Error! Block not accepted
Error! Block not accepted
Error! Block not accepted
Error! Block not accepted
Error! Block not accepted
keeps on looping.
should I click stop and try to switch the phone on?
_________________
Oxygen Inc
[ This Message was edited by: amnesia on 2005-05-06 15:51 ] |
gbrooks3
Joined: Jun 02, 2003
Posts: > 500
From: OTP RED CID36
PM, WWW
|
you tried to finalize the recovery flash? Flash the recovery file again without finalizing this time. you can use 460800 aswell. |
amnesia
Joined: Jan 15, 2004
Posts: > 500
From: Doha, London, Tokyo, Shanghai
PM, WWW
|
the recòvery only has a Main no FS. that's normal right?
|
|
|
Posted: 2005-05-06 15:31
