| Author |
T39m : i did something really wrong. help & opinion needed |
tictac-octeam
Joined: Nov 17, 2004
Posts: 12
PM, WWW
|
I just bought used T39m 3days ago... and i got T28 Service cable(Serial).
I success converting the T28 service cable into data cable(Pin 6 to 4 , Pin 7 to 5, no pin 9) ...
PC able to recognize my phone when i used Hyper terminal, I already managed sending new background logo to my T39m, and Dial Up netwok able to recognized my T39m modem as well
Everything when fine... except each time i trying to dial up to internet through my PC -> T39m
It will connect & Verify user name & password... then disconnect it..
I can see my T39m screen showing connecting while dialing... then it just auto disconnect
This is where the problem start...
- i open hyperterminal again
and i set the baud rate speed to 115200... and save it with this command AT&W=0
the phone reply : OK
- then when i trying to dail again... my phone restart...
And now my pc cannot detect it anymore, Hyperterminal get no response as well, My pictures ... same , Dial up netwrk.. same
I Had try connecting with all baud rate from 1200 to 115200 .... no go  . Master reset... done... no go
Can anybody help me reset the setting with the hyper terminal?
Is there anyway i can clear the phone cmos? |
|
|
tictac-octeam
Joined: Nov 17, 2004
Posts: 12
PM, WWW
|
BTW.. here is my current Firmware
R2S001 CXC12568
R2S001 CXC125147_TAE |
*Jojo*
Joined: Oct 15, 2003
Posts: > 500
PM |
@tic-tac-toe - Glad to have you on-board Esato mate  Regarding your problem, maybe @bobafett can help you here, you can simply send him a Private Message dude. Good Luck ! |
BobaFett
Joined: Jan 06, 2004
Posts: > 500
From: Kamino (wish it would be Lund)
PM, WWW
|
@tictac welcome here! Pls pm wapt, he might help u in such tech things. Btw u should do an upgrade to r4a008. Is it an m or mc, never saw r2s fw before.
This message was posted from a T68i |
tictac-octeam
Joined: Nov 17, 2004
Posts: 12
PM, WWW
|
Ya it is T39m....
i can browse with gprs on my phone... no problem... it can connect 6hours non stop... Love this T39m 
Ya... i'm thinking of flashing to new firmware as well... as it will reset all setting back to factory
I got R4A008 fw & service cable on my rig....
all i need now only Flashing software... i'm still looking for this tools
If any of you have 1... here my email : nastechxtreme2@yahoo.com
Cheers & glad to be here
tictac
|
tictac-octeam
Joined: Nov 17, 2004
Posts: 12
PM, WWW
|
Is there any other solution than flashing newer fw? Should i get IR or bluetooh connection? [:]
This message was posted from a T39 |
ESTOR
Joined: Apr 20, 2002
Posts: > 500
From: Singapore
PM |
The 1st thing I would try is a master reset. You'll lose your phone book and stuff, as you probably already know. Oops.. you already did that.
On your hyper-terminal, try setting the baud rate to slower speed, try all of them, and see if you can get a connection after each trial. use ATI command to see if you get response.
As for remote computer not allowing access, most ISP restrict ISDN access at slow speeds such as what you'll get with your T39.
[ This Message was edited by: ESTOR on 2004-11-17 23:00 ] |
BobaFett
Joined: Jan 06, 2004
Posts: > 500
From: Kamino (wish it would be Lund)
PM, WWW
|
@tictac bit off topic, but get a bhc10 high cap batt and u ll surf 3 times longer on gprs. And try this in standby mode *#05# ps: the hiden snake game is at erix when the title pops up, push 1 2 3 or 7 8 9
This message was posted from a T68i |
tictac-octeam
Joined: Nov 17, 2004
Posts: 12
PM, WWW
|
Ok i will try again later! Is the any way to by pass ISP auto disconnect system?
This message was posted from a T39 |
tictac-octeam
Joined: Nov 17, 2004
Posts: 12
PM, WWW
|
I tried that *#05# all i get code not match & asking for puk no! The snake work! Thx
This message was posted from a T39 |
tictac-octeam
Joined: Nov 17, 2004
Posts: 12
PM, WWW
|
I got R2S001 on my T39m! Should i upgrade to new fw? My port speed set to 115kb by default! Is there any way i can reset it back to factory setting? I use this command with hyperterm:
ATE AT+IPR=115200
AT&W=0
This message was posted from a T39 |
BobaFett
Joined: Jan 06, 2004
Posts: > 500
From: Kamino (wish it would be Lund)
PM, WWW
|
Yes, go for an upgrade! Visit se and ask for r4a008.
This message was posted from a T68i |
tictac-octeam
Joined: Nov 17, 2004
Posts: 12
PM, WWW
|
This is how to reset it back to factory set: AT&F ;
AT&W=0 ; :-]
This message was posted from a T39 |
|
|
Posted: 2004-11-17 11:43
