| Author |
Anyone know what this means? |
Sardara
Joined: Jan 04, 2002
Posts: 56
PM |
After a backup, when I switch my phone on again, before getting to the main phone screen, this message comes up :
"PROGRAM CLOSED.
Program AppArcServerThred
Reason Code : USER
Reason Number : 130 "
Anyone know what this means and have any of you had this meassage come up. This happens after every backup for me. |
|
|
tangws
Joined: Apr 03, 2003
Posts: 19
PM |
I have the same problem. It used to be ok. Posted to the forum but no responses so far.
|
evoke
Joined: Mar 05, 2002
Posts: > 500
PM |
maybe just worth trying reinstalling the phone monitor sw if u cant get an answer
[addsig] |
Eamonn
Joined: Nov 30, 2001
Posts: > 500
PM |
I have the same message. have just learnt to ignorit now.. |
jplacson
Joined: Apr 21, 2002
Posts: > 500
From: Philippines
PM, WWW
|
I think this is AppForge. I get that as well..I just ignore it. |
Eamonn
Joined: Nov 30, 2001
Posts: > 500
PM |
I don't have AppForge installed on my P800..
|
lloydcody
Joined: Apr 13, 2003
Posts: 150
From: Wales
PM, WWW
|
I think its just a program exception error. Like getting a general protection fault or critcval error in Windows. It's when a program tries to do something that is not physically possible so the phone can't understand what to do so just closes the app. E.g. If a program tries to dived a number by zero - if there is no code to check for this then the phone has no option but to close the app as there is no 'answer' to this problem (cant understand infinity unless programmed to do so!).
Could be wrong - sorry for not being specific.
Hope this helps!
LLOYDY |
Sardara
Joined: Jan 04, 2002
Posts: 56
PM |
Thanks for all the info dudes. Glad I'm not the only one with this problem and so long as phone works fine, I'll just ignore it. |
psikey
Joined: Jan 31, 2002
Posts: > 500
From: UK - South Yorkshire
PM |
I had this & couldn't figure out how to get rid of it (even with a hard reset!)
Since upgrading to R2D it has gone  |
savvas
Joined: Jan 21, 2003
Posts: 158
From: Cyprus
PM |
It means that must go and get your P800 upgraded! 
_________________
Addicted to minesweeper.Expert:190sec
[ This Message was edited by: savvas on 2003-05-11 13:10 ] |
Andy_P
Joined: Jun 10, 2002
Posts: > 500
From: Warwickshire
PM |
division by zero doesn't equal infinity... |
lloydcody
Joined: Apr 13, 2003
Posts: 150
From: Wales
PM, WWW
|
there r an infinite number of zeros in 1!
What's ur idea of infinity then?
LLOYDY |
searley
Joined: May 13, 2003
Posts: 81
PM |
I have had this a couple of times..
When you start a backup, all items are shut down, then phone restarted in backup mode.
when backup is complete the phone should shut down, i have noticed that sometimes it doesn't it just blanks the screen and stop the backup software!
when using the power button you get the error stated in the above posts as not all require drivers etc are running.. a simple reboot and all is fine.
the times the phone pwersdown properly all is ok
|
dr_sy
Joined: May 18, 2003
Posts: 144
From: Chelmsford, Essex
PM |
Hi, I had this when backing up when I had active desk installed. I uninstalled it and it was fine
Regards
Sy |
Orobas_Wats
Joined: May 14, 2003
Posts: 99
From: Kent, UK
PM |
Divide by Zero is undefined, not infinity, otherwise it would be really easy to get computers to deal with divide by zero, my life would be a million times easier if someone would just sit down and say "Right, divide by zero equals ..." 
as for the problem, I don't know sorry, but it would deffinately be worth trying to get your firmware upgraded
-Orobas |
|
|
Posted: 2003-05-10 09:38
