Esato

Forum > Sony Ericsson / Sony > Software, Firmware and Drivers > DaVinci with k700i, "press power button" but then?

Author DaVinci with k700i, "press power button" but then?
Fastomat
T68 gold
Joined: Oct 02, 2005
Posts: 8
PM
Posted: 2005-10-02 00:20
Reply with quoteEdit/Delete This PostPrint this post
Hi.. tried google and searched this forum but didn't find the helping answer yet. I got an unlocked voda k700i and want it unbranded. Got 1 credit from davinci, using their 13.9 software. Check Available ports tells me the DSS-20 is on COM3 so I select DSS3 there.
The phone is switched off and on the DSS-20. Then when I press "Read CID/Test cable" I get a message about 1 credit,
**** READING CID STARTED****
Shortly press Power button!
but that's it. When I press it my phone goes on, asks for my PIN but nothing happens on davinci even if I wait 10 mins. It has worked 1 time a few hours ago it detected a k700i then but I can't figure out what I did different that one time. Anybody got a clue what I do wrong? Thanks.
Fastomat
T68 gold
Joined: Oct 02, 2005
Posts: 8
PM
Posted: 2005-10-02 01:05
Reply with quoteEdit/Delete This PostPrint this post
Funny.. found the problem. The trick was to remove the battery, put the phone on the DSS-20 and then put the battery in.

Now a different challenge:

Client Version 13.9
Getting data from server...
Connection ok! Data recieving...
Credits: 1 Counter: 0
Shortly press Power button!
Detected SonyEricsson: K700/K300/J300/K500/S700/Z500.
Status Ok, OTP Close, CID29, PAF1
IMEI: 354006-00-050320
Loading Main File. Ok!
Loading FS File. Ok!
Flash File CID:36
Phone CID:36
Flashing 217 blocks...
Block Not accepted
Execution Time - 00:00:32
Error: 0x005556

Main: K700i_MAIN_EU_EMEA_US_AL1_R2AY004_CID36.DVT
FS: K700i_FS_EU3_R2AY004_CID36.DVT
CDA: CDA102337/11 - Europe3

After this my phone just powers on like nothing happened. Any1 got an idea? thanks.
Calvin Calv
T68 gold
Joined: Jun 27, 2005
Posts: 1
PM
Posted: 2005-10-03 06:37
Reply with quoteEdit/Delete This PostPrint this post
i think u have load with the wrong flash files..... ur phone is cid29 but u used cid36.... try to use cid29 flash files
Fastomat
T68 gold
Joined: Oct 02, 2005
Posts: 8
PM
Posted: 2005-10-03 11:50
Reply with quoteEdit/Delete This PostPrint this post
Umm.. I see 2 confusing things:

Status Ok, OTP Close, CID29, PAF1
Phone CID:36

CID29 and CID36. (?)

Before I screw up my phone, anybody who can confirm I need to use the CID29 to 36 flash from davinci 1st?


[ This Message was edited by: Fastomat on 2005-10-03 11:09 ]
Krubach
T39 black
Joined: Dec 05, 2002
Posts: > 500
From: Sunny Portugal! :)
PM
Posted: 2005-10-03 11:59
Reply with quoteEdit/Delete This PostPrint this post
Why don't you try Davinci support forum?
That's the correct place to put your questions. [addsig]
Fastomat
T68 gold
Joined: Oct 02, 2005
Posts: 8
PM
Posted: 2005-10-03 12:06
Reply with quoteEdit/Delete This PostPrint this post
Sure.. where's the link? I'm only a member of esato yet.
Fastomat
T68 gold
Joined: Oct 02, 2005
Posts: 8
PM
Posted: 2005-10-03 12:57
Reply with quoteEdit/Delete This PostPrint this post
@Calvin Cav

I used the K700_TRANSFORM_CID29_to_CID36.DVT and it accepted, but the phone went back to CID29.
Phone CID: 29

And when I try to use CID29_to_CID36 again I get this at 25%:

Client Version 13.9
Shortly press Power button!
Detected SonyEricsson:
K700/K300/J300/K500/S700/Z500.
Status Ok, OTP Close, CID29, PAF1
IMEI: 354006-00-xxxxxx
Loading Main File. Ok!
Flash File CID:29
Phone CID:29
Flashing 4 blocks...
Block Not accepted
Execution Time - 00:00:16
Error: 0x005556

I got a non-working phone now and no clue what to do

I can flash both the R2AY004 (Main and FS) now but with a warning of CID mismatch. That won't work right?
Can anybody help me?

[ This Message was edited by: Fastomat on 2005-10-03 11:58 ]

[ This Message was edited by: Fastomat on 2005-10-03 12:00 ]
Krubach
T39 black
Joined: Dec 05, 2002
Posts: > 500
From: Sunny Portugal! :)
PM
Posted: 2005-10-03 15:13
Reply with quoteEdit/Delete This PostPrint this post
I hate lazy people.

http://www.seuniverse.com/forums/forumdisplay.php?f=30 [addsig]
Fastomat
T68 gold
Joined: Oct 02, 2005
Posts: 8
PM
Posted: 2005-10-04 00:31
Reply with quoteEdit/Delete This PostPrint this post
I had seen that one, just didnt recognise it as "the" davinci support forum. Sorry m8.

Anyway it's all working now. I thought the CID29 to CID36 file was some sort of transform on your phone and that you would see something had changed after its done.
But no, it appears its only making sure you can load the CID36 software on a CID29 phone. So just push the ignore CID option, don't pay attention at the warnings of CID mismatch and as long as everything loads you can finalize and will be ok. I was thinking too difficult and was paying too much attention about what was going on. The phone has the latest version now, menus are way faster, the battery lasts way longer already noticeable and no more ugly vodjefone customisations.


[ This Message was edited by: Fastomat on 2005-10-03 23:33 ]
Access the forum with a mobile phone via esato.mobi