Forum > Sony Ericsson / Sony > Software, Firmware and Drivers > Super camera driver for k750/w800/w810

On 2007-08-20 22:51:06, lpachuong wrote:
A4A 6.2

Hello everyone. It is unbelievable that in just one day there has been 3 version of A4A My bad, my bad. This time, thanks to Power_Vano who has point out a problem in full range shot in night mode or low light . Here is a new fixed: http://www.mediafire.com/?8mzfix9xjfy

Changes

-Full range pictures at night without light source can be take with Led+Macro+Night mode+exposure 1.4+FIne quality+infinity focus for the best quality (exposure maybe reduced) These parameters have been tested by me many times and my phone was really hot
- Close range shot at night witout light source : Led+Macro+Night mode+FIne quality+ autofocus You dont need to change exposure since autofocus will get the correct exposure for you. Here are some close-up pictures:

The full size pictures of these two images are better. I will upload the link later.

- When you take picture indoor at night with light on, please move to Normal quality for low exposure. (Macro still on)

In brief:

Always use macro
--
Fine quality for {outdoor shot} or {indoor shot in the morning/afternoon with exposure around 1.5) or (close range shot within 10-60cm with led+nightmode+autofocus)
---
Normal quality for indoor shot at night with light source in case you get overexposure in fine quality and you dont like adjusting exposure (This is not my strong suggestion)
---
Led+nightmode on+macro will work but It is difficult to get nice picture with this phone-camera bcz you will need dozens of medicine to stop your shaking hand
---
When you switch between fine quality and normal quality, the first picture will have the effect from the previous quality(EM on/off) . I don't know how to fix it now, but it works fine at the second shot
---
The best way to understand how to control overexposure is to play with different parameters and you will know what exposure is suitable at certain places.
---
I will be online for the next 45mins after watching Detective Conan 468 on veoh.com and then I will go to bed. So, see you later and sleep well

Thank you everyone.
Best regards



_________________
To be or not to be !!!
W800i/K750i driver: A4A - 4.5 11/08/2007
http://www.freewebs.com/ict2006_2007/A4A_4.5.RAR

[ This Message was edited by: lpachuong on 2007-08-20 23:21 ]

On 2007-08-20 22:51:06, lpachuong wrote:
...
When you switch between fine quality and normal quality, the first picture will have the effect from the previous quality(EM on/off) . I don't know how to fix it now, but it works fine at the second shot
...

On 2007-08-20 22:01:04, DarKMaGiCiaN wrote:
BACK ^_^
LONG TIME .....

I reseved lots of emails from people who want more supermode functions in DarKMaGiCiaN 0.92
because of that I'm here with new Driver
actually it is DrKMaGiCiaN Driver with Jonaugust_69
Professional Camera Driver v8.64 functions + mod for CID49 phons
(( 0.92 Professional Camera Driver ))


Link: http://www.mediafire.com/?8flmymnzhbj

User Guide
------------------------------------------------
first layer of menus(marco off)

EV-2.0=Scene (1.0 -1.9) 1.0 is Default AutoExposure (1.1Portrait 1.2Landscape 1.3Twilight Portrait 1.4Twilight Landscape 1.5Sports 1.6Beach/Snow 1.7Document
EV-1.7=Contrast (1.1 -2.7)
EV-1.3=JPEG_LEVEL (1.0 -4.0) 34% - 94% step 2
EV-1.0=Manual Shutter Speed (1.0 -4.0) 1.0 is AUTO Day(1/5000 - 1/6) Night(1/5 - unknow)
EV-0.7=ISO (1.0 -2.3) 1.0 is AUTO
EV-0.3=linear zoom(1.0-4.0)(1X to 16X)
EV 0.0=original EV (1.0 -3.5)(can be changed with Manual Shutter Speed together)
EV+0.3=Manual Focus (1.0 Autofocus, 1.1 Focus to Infinity, Manual Focus Range 1.2-4.0)(support zoom)
EV+0.7=Manual WB
EV+1.0=Manual effect
EV+1.3=Spot (1.0 -1.7)1.0 is Default, 1.1 SPOT, Others unknow
EV+1.7=CC(green to red) (1.0-4.0),(00~7F)green (ff~80)red
EV+2.0=CC(yellow to blue) (1.0-4.0),(00~7F)yellow (ff~80)blue

second layer of menus(marco on)

EV-2.0=Brightness (1.0 -2.5)
EV-1.7=Contrast (1.1 -2.7)
EV-1.3=Sharpening (1.1 -2.7)
EV-1.0=Hue(1.1-4.0)
EV-0.7=Saturation(1.1-4.0)
EV-0.3=Focus setting(1.0-1.5)(1.0 marco mode 1.1 normal mode 1.2 full range 1.3 Fast mode 1.4 Fast mode and full range 1.5 Macro mode)default 1.0
EV 0.0=original EV (1.0 -3.5)(can be changed with Manual Shutter Speed together)
EV+0.3=Manual Focus (1.0 Autofocus, 1.1 Focus to Infinity, Manual Focus Range 1.2-4.0)(support zoom)
EV+0.7=Manual WB
EV+1.0=Manual effect
EV+1.3=Spot (1.0 -1.7)1.0 is Default, 1.1 SPOT, Others unknow
EV+1.7=mirroring(1.0 to 1.3)(1.0Horizontal mirroring 1.1Horizontal mirroring 1.2Vertical mirroring 1.3Vertical mirroring)
EV+2.0=SlowShutter (1.0 -4.0) 1/20' to 2' (can be changed with ISO together)

have fun ^_^

[ This Message was edited by: DarKMaGiCiaN on 2007-08-20 21:27 ]

On 2007-08-20 22:51:06, lpachuong wrote:
A4A 6.2

Hello everyone. It is unbelievable that in just one day there has been 3 version of A4A My bad, my bad. This time, thanks to Power_Vano who has point out a problem in full range shot in night mode or low light . Here is a new fixed: http://www.mediafire.com/?8mzfix9xjfy


_________________
To be or not to be !!!
W800i/K750i driver: A4A - 4.5 11/08/2007
http://www.freewebs.com/ict2006_2007/A4A_4.5.RAR

[ This Message was edited by: lpachuong on 2007-08-20 23:21 ]

On 2007-08-21 06:26:47, terminator17 wrote:


hey can u tell me whats d difference in this driver and jonaugust driver??
thanks

I'm sorry to see that there are stability issues with some K750 and W800 phones with Sarmad 5.8.. unfortunately, there isn't too much I can do since I have designed the driver for the W810 (the phone I have).. I might make a K750 version in the future, I'm not sure.. but if a W810 user has crashes, please let me know.. as that should not happen.

On 2007-08-21 01:40:03, Raiderski wrote:


seq_ss_take=$c6 00
#DEF_SHOT
$cl
#IMP_SHOT
$cx

well, if something has to be wrong then it is only register 6 faulty usage. take care of $s6 and $b6 commands in whole code. i used reg 6 as a storage for individual bits to describe various driver features states. because of this idea, reg 6 in your driver has many collisions, for example: set any WB color to automatic (1.0) value and snapshot will be taken with EM usage (reason is $b6 01 7 1), after camera open 1st picture is always with EM. after EM shot every next shot will be without EM