| Author |
K750i EU_1 & R1N035 = no update yet. |
Redback
Joined: Sep 20, 2004
Posts: 32
From: Sydney
PM |
To the Aussies,
I'm from Australia too and new in all this upgrading firmware stuff. How come a few people updated with no probs from SEUS Australia site and other people have had problems?
I've downloaded the update drivers, software and was ready to roll last night but was too scared of crashing my phone after reading this forum.
I'm running R1J002 with no major problems but R1N looks much better.
So what do I do? It doesn't even tell you what the latest firmware is on SEUS. I don't want to upgrade & end up with R1L. And I don't want to use Da-vinci.
Has it been verified that R1N is available on the Aussie SEUS? Anything I should know since it's my first time upgrading??
Thanks in advance.. |
|
|
screwed
Joined: Sep 12, 2005
Posts: 28
PM |
There has been no updates in UAE, Middle east. and its wednesday! ahh when will they put it on! |
mephisto2k
Joined: Jun 14, 2005
Posts: 87
PM |
Quote:
|
On 2005-09-14 04:24:38, BUFFBOY wrote:
ok guys
here what i done
originaly my phone was with optus branded. i debranded with devinci to
CDA Number: CDA102338/38
CDA Revision: R6A
Model: K750i
Language Variant Name: EUROPE_2
firmware after that was
R1L002
prgCXC125952_EU_1_CLR1L002
few minutes ago i used devinci again to change the CDA to 102337/10
spent another $10 eros
then i went to the SE site and update was allow to R1N035
|
|
Have I missed a step. I also have CDA102338/38, bought a credit and used DaVinci to set CDA to 102337/10. The log said it was applying the new CDA, it completed without error but when I went to SEUS it still started downloading L002, so I checked my Software Info and it still says 38/38!!!
I even did a Master Reset in case but it's still the same!
Have I wasted a credit? 
[ This Message was edited by: mephisto2k on 2005-09-14 08:38 ] |
BUFFBOY
Joined: Jul 20, 2005
Posts: > 500
From: Sydney
PM |
Quote:
|
On 2005-09-14 09:37:38, mephisto2k wrote:
Quote:
|
On 2005-09-14 04:24:38, BUFFBOY wrote:
ok guys
here what i done
originaly my phone was with optus branded. i debranded with devinci to
CDA Number: CDA102338/38
CDA Revision: R6A
Model: K750i
Language Variant Name: EUROPE_2
firmware after that was
R1L002
prgCXC125952_EU_1_CLR1L002
few minutes ago i used devinci again to change the CDA to 102337/10
spent another $10 eros
then i went to the SE site and update was allow to R1N035
|
|
Have I missed a step. I also have CDA102338/38, bought a credit and used DaVinci to set CDA to 102337/10. The log said it was applying the new CDA, it completed without error but when I went to SEUS it still started downloading L002, so I checked my Software Info and it still says 38/38!!!
I even did a Master Reset in case but it's still the same!
Have I wasted a credit?
[ This Message was edited by: mephisto2k on 2005-09-14 08:38 ]
|
|
use devinci unlocker k750flasher_13.7.exe and select the 102337/10 and simply flashed it.. 100% done, then use SE site to get latest r1n
not much to explain.. better off adding someone on msn and run you thru
add me
suckonmydick@hotmail.com
ps its my real msn
|
assembler
Joined: Nov 17, 2004
Posts: 6
PM |
hi my fone's from australia and i have been trying to update my fone which is on
R1L002
prgCXC125952_EU_1_CL but it the update thingy keeps on saying i have the latest version :S i thought the new firmware was already avaliable for australia or am i doing something wrong |
robpiggott
Joined: Jun 20, 2005
Posts: 3
PM |
got my update today with eu1 previous software. im in the uk using a unbranded mobile on the virgin network. noticed a sligh difference in the update in that it downloaded a further file during the update process that i was not doing the other day. only a slight difference but when it happened i was pleased...now to go off and play to see the improvements. |
DynaMight
Joined: Aug 06, 2003
Posts: 23
PM |
Quote:
|
On 2005-09-14 04:24:38, BUFFBOY wrote:
ok guys
here what i done
originaly my phone was with optus branded. i debranded with devinci to
CDA Number: CDA102338/38
CDA Revision: R6A
Model: K750i
Language Variant Name: EUROPE_2
firmware after that was
R1L002
prgCXC125952_EU_1_CLR1L002
few minutes ago i used devinci again to change the CDA to 102337/10
spent another $10 eros
then i went to the SE site and update was allow to R1N035
now i have the latest firmware.
ps im located in australia.
my latest firmware now is
R1N035
prgCXC125952_EU_1_CL
R1N035
LCD SW versions
Main display
Current: 0
Camera SW versions
Camera
Current: 4.5
ITP SW version
CXC 125 932 R1D
Customization
CDA102337/10 R6A
cxc125953 R1N035
1E0W
EUROPE_2
Content version
PA19
|
|
I just followed this on my Branded 02 UK phone (which wouldnt update) and after I followed the above it updated first time! |
Redback
Joined: Sep 20, 2004
Posts: 32
From: Sydney
PM |
Well finally I have R1N0035! Thanks for the help Buffboy(msn)
This is for the begginers...
Basically, your CDA has to be 102337/10 R6A to enable you to upgrade to R1N. Check this on your firmware by scrolling down the page "Software Info"
If that is the correct CDA then go ahead & update on SEUS.
If not you'll have to flash it to another region's firmware using http://www.davinci.com , flash it to EU_2 and 102337/10 R6A
Make sure you follow the instructions properly! And when you do the SEUS make sure you have the update drivers downloaded!
[ This Message was edited by: Redback on 2005-09-15 02:49 ] |
max_wedge
Joined: Aug 29, 2004
Posts: > 500
From: Australia
PM, WWW
|
thanks for that info redback - I have cda 102338/55 R9A
(eu_1 and europe_2)
So I guess there's no point in me updating yet. Any idea if that means those cda's will never update, or just not available for those customisations yet? |
Redback
Joined: Sep 20, 2004
Posts: 32
From: Sydney
PM |
Thats what I was asking Buffboy cause I didn't wanna flash with davinci, I thought if I waited SEUS will eventually add other CDA regions. But he reckons they won't so go do the flash. Just read the support forum(and laugh at the spelling lol) and make sure you do everything properly.
Go to the manual section in davinci & read the k750i flash tutorials, it'll show you what to do. Oh yeah & make sure you donwload the 13.7 Client NOT the 13.8 client. Apparently the cable only works with the 13.7
Let me know how you go..
|
assembler
Joined: Nov 17, 2004
Posts: 6
PM |
yea, thanks red back! no wonder, y CDA is 102338/59 so it won't update.. |
visionoflove
Joined: Aug 27, 2005
Posts: 5
PM, WWW
|
i have CDA 102337/12 R4A cxc125953 R1L002
EUROPE_4
Any one have been successful with upgrading to THE NEWEST firmware? |
Viper6
Joined: Sep 13, 2005
Posts: 4
PM |
Hi guys
I am from Australia too and I bought an unbranded K750i for $750 outright...
I was just about to come here swearing about how angry I was that I haven't been able to update my firmware all this time, and I was about to write a nasty email to SE as well...
Anyway, I just went to try the update one more time before getting really angry, and it actually worked! I've tried about 15 times ever since the new firmware was out and kept getting the same stupid error that I had the latest firmware, even though I know I didn't.
Well now I am happy to say I do, and first impressions are VERY positive....
Menu speeds are definately faster. As are loading of java games, and the picture quality of the games (at least the tennis game) has definately increased! Before I couldn't see the ball half the time but now its much more clearer and looks a lot better.
Thumbs up from me so far, well done SE. I will test the camera and volume out tomorrow but so far so good!
My firmware before the update was as follows:
R1L002
prgCXC125952_EU_1_CLR1L002
R1L002
Customization
CDA 102338/59 R4A
cxc 125953 R1L002
EUROPE_2
Hope you guys get your update soon  |
Fabio 182
Joined: Sep 15, 2005
Posts: 6
From: Perth
PM |
Hi All,
I use DaVinci to flash my phone to CDA 102337/10 from 102338/55 as I read on this forum that this will allow it to update via SEUS. It flashed successfully however when I have a look at my Service Info it is still coming up with the old CDA. This brings me to believe that either DaVinci is a crock or that the CDA 'On Screen' doesnt change.
Any thoughts?
P.S. It still wont update to R1N via SEUS...wtf? |
Redback
Joined: Sep 20, 2004
Posts: 32
From: Sydney
PM |
@ Fabio,
You must've done something wrong while updating with Davinci. It does show your correct firmare/cda through the service menu. Mine was R1J002 then I flashed it to R1L002 on Davinci which allowed me to do the upgrade to R1N0035 on SEUS.
@ Viper6 - So the update finally worked with you on cda /59 R4A? So I wasted $15 on davinci to flash? lol hmm maybe SE have started adding other cda's to the SEUS or something I don't know. Mine wouldn't work until I got it flashed. The only problem on R1N is I still get blue lines on night shots. Check my shots of Sydney Harbour in the K750 pics topic in General Forum. |
|
|
Posted: 2005-09-14 08:27
