| Author |
Is it Possible to recover from a flash failure? |
puerrican85
Joined: May 27, 2005
Posts: 28
PM |
ok i tried flashing the file from the forum link u sent but i get this error
GUI v0.8975062/COM
client-server version engaged.
HARDWARE ID:A12773F5DFA018352E0B22C7BED6B32F
Loaded 24 flash descriptors
Open COM port OK
ChipID is 71000301
CID detected:29
PHONE IS RED RETAIL PRODUCT
Speed:115200
rsa request not accepted
RECOVERY MODE STARTED
rsa request not accepted
Open COM port OK
Stop signal set.
rsa request not accepted
All possible recovery loaders fail. That phone not supported
Phone can't boot,sorry.
Elapsed:49 secs.
so now im at abit of a loss. i'll keep trying and charge the battery. Ironically from my last firmware try it went to 100/250 blocks so atleast i see a light go one when connected to a charger.
Any ideas on how to flash Erom? |
|
|
gbrooks3
Joined: Jun 02, 2003
Posts: > 500
From: OTP RED CID36
PM, WWW
|
Strange. you have correct comport selected? And pressed the power button?
Because the platform sends bogus messages while charging, that is why!!!..But why this change of heart?..We sense a charger connected, oops, we will not shut down after all!!!..*********************** UI BASIC, HOLD YOUR HORSES
|
puerrican85
Joined: May 27, 2005
Posts: 28
PM |
yeah its the same com port i used for davinci aswell. I even tried charging the phone for an hour and tried again but the same result. |
sailaab
Joined: May 19, 2005
Posts: > 500
From: India
PM |
In God we trust ! :-)
>>> And may God bleSs ya Bro ! Incase Gods outta reach try SE Serv Cntr.
>>>
Usually Flash crashes r hard to recover [w/o hardware stripping soldering n stuff] But this time let rite ppl handle it !
This message was posted from a S700 |
gbrooks3
Joined: Jun 02, 2003
Posts: > 500
From: OTP RED CID36
PM, WWW
|
haha dont listen to guy who just posted, he obviously is not to familair with the makeup of SEMC firmware. Soldering stuff lol
Well, i guess setool isnt working for you (cable com or os issue i think)
So give the davinci recovery file ago. Also see if you can get another battery from anothe phone or charge the bad one in it.
Because the platform sends bogus messages while charging, that is why!!!..But why this change of heart?..We sense a charger connected, oops, we will not shut down after all!!!..*********************** UI BASIC, HOLD YOUR HORSES
|
puerrican85
Joined: May 27, 2005
Posts: 28
PM |
my guess is the battery is reaaaally dead. imma let it charge for a loong time and then try again. Cuz it hasnt charged a whole lot. But i also notice i cant flash at all if i go at rate of 38400, 57600 only works for about 1 min and 115200 doesnt go at all. Maybe the cable is abit f'd up?
Edit: Yeah imma the battery, cuz now i see the red light on so atleast i kno its charging. From what i heard from your previous posts gbrook is that a good refreshed battery will help. but still wondering why only the lower speed rates work
[ This Message was edited by: puerrican85 on 2005-05-28 00:34 ] |
gbrooks3
Joined: Jun 02, 2003
Posts: > 500
From: OTP RED CID36
PM, WWW
|
What cable are you using? T28 only supports 115200. Other speeds with USB are affected becuase the V800 is a Marita chip phone  Cannot be flashed at full speed.
Because the platform sends bogus messages while charging, that is why!!!..But why this change of heart?..We sense a charger connected, oops, we will not shut down after all!!!..*********************** UI BASIC, HOLD YOUR HORSES
|
puerrican85
Joined: May 27, 2005
Posts: 28
PM |
yeah im using a T28, u say it only supports 115200? but lower speeds will work right? it kinda was working for me lol. So then what about usb cables? will they help fasten the process or is still useless since u said the v800 cant go full speed. |
gbrooks3
Joined: Jun 02, 2003
Posts: > 500
From: OTP RED CID36
PM, WWW
|
Sure can go slower but Marita chip only supporting maximum baud 460800.
I really suggest you get another battery, then flash EROM or Davinci Recovery file and then do a full reflash.
_________________
Because the platform sends bogus messages while charging, that is why!!!..But why this change of heart?..We sense a charger connected, oops, we will not shut down after all!!!..*********************** UI BASIC, HOLD YOUR HORSES
[ This Message was edited by: gbrooks3 on 2005-05-28 00:48 ] |
puerrican85
Joined: May 27, 2005
Posts: 28
PM |
easier said then done, been trying to flash with setool with a fresh battery and still same error. Damn,.....
wat is rsa anyway?
|
gbrooks3
Joined: Jun 02, 2003
Posts: > 500
From: OTP RED CID36
PM, WWW
|
Thats nothing to worry about. I dont think you have setool set up correctly, becuase it does work - and you 100% have EROM erased problem - i see it nearly everyday.
If you have another PC try with that. Otherwise i will need to speak with you on MSN or ICQ or whatever.
Because the platform sends bogus messages while charging, that is why!!!..But why this change of heart?..We sense a charger connected, oops, we will not shut down after all!!!..*********************** UI BASIC, HOLD YOUR HORSES
|
puerrican85
Joined: May 27, 2005
Posts: 28
PM |
im on msn now, email is puerrican85@hotmail.com
i'll be on till 1 in the morning so message me if u can gbrook.
thanks alot |
puerrican85
Joined: May 27, 2005
Posts: 28
PM |
Heres a pic of the setool window
u should be able to make out most of whjat it says.
Esato reduced the size |
gbrooks3
Joined: Jun 02, 2003
Posts: > 500
From: OTP RED CID36
PM, WWW
|
Strange, all looks good. Have you any antivirus? Firewall? Power managment activated? If so turn it all off.
Because the platform sends bogus messages while charging, that is why!!!..But why this change of heart?..We sense a charger connected, oops, we will not shut down after all!!!..*********************** UI BASIC, HOLD YOUR HORSES
|
Residentevil
Joined: Feb 29, 2004
Posts: > 500
From: Raccoon City, USA
PM, WWW
|
Only if you are lucky.
Tough times don't last, tough people do!
Free Tibet |
|
|
Posted: 2005-05-27 23:59
