Posted by AlexRussell
So, my k800i is dead (won't start), so I tried flashing it, the flash succeeded, but the phone still don't start...
So whats the problem with my phone?
What else should I try to revive it?
It has a corrupted EROM?
Should I try to update it with SE update service?
Thank you.
My XS++ log.
08:05:26| XS++ v3.1 (Darwin) Ready !
08:05:26| Executed on Microsoft Windows XP
08:05:39|
08:05:39| Attempting to open the interface...
08:05:39|
08:05:39| TURN OFF PHONE!
08:05:39| Hold 'C' button on phone and connect phone NOW.
08:05:39| You have 30 seconds...
08:05:39|
08:05:58| Baseband ID: 9900
08:05:58| Protocol Version: 3.1
08:05:58| Warning: IMEI name does not match GDFS name (IMEI:K800 GDFS:K810)
08:05:58| ...using IMEI name
08:05:58|
08:05:58| Profiling SEMC phone...
08:05:58| Platform: DB2020
08:05:58| OTP CID: 51
08:05:58| EROM CID: 52
08:05:58| EROM Color: Red
08:05:58| IMEI: 35570401xxxxxx
08:05:58| Phone ID: K800
08:05:58| Region: MEDITERR
08:05:58| CDA: CDA102568/1 R2A
08:05:58| Firmware Version: R6BC002
08:05:58| EROM: R3A099
08:05:58| Ready for operation!
Any firmware for my k800i so I can turn it on?
[ This Message was edited by: AlexRussell on 2011-10-29 16:08 ]
Posted by Lollylost100
Try an update but your best bet would be paying for an Omnius licence and fixing it that way.
Posted by AlexRussell
On 2011-10-29 15:47:48, Lollylost100 wrote:
Try an update but your best bet would be paying for an Omnius licence and fixing it that way.
Ok, I will try, but I want to know whats the problem with it, its a corrupted EROM, right?
Posted by Lollylost100
What does it do when you try to start it?
Posted by AlexRussell
I haven't update it yet with SE service updater, it still doesn't start, I tried with SEtool2 I clicked "Unlock/Repair" button this is the log...still not working ):
Welcome to SEtool2 ( LITE edition ) v 1.11
supported DB2010/DB2012 CID49/50/51/52, DB2020 CID49/51/52
Loaded 51 flash descriptors
if you like LITE edition - please visit http://www.setool.net and buy FULL.
"Unlock/Repair" button log:
ChipID:9900,EMP protocol:0301
PHONE IS RED RETAIL PRODUCT
FLASH CID detected:52
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:35570401478243 CERT:RED
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
loader startup: executed
loader GDFS startup: executed
USERCODE reset to 0000
Elapsed:27 secs.
"Read GDFS" button log:
Will backup GDFS now.
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:35570401478243 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
loader startup: executed
loader GDFS startup: executed
stated number of vars:1317
Found:832 variables
Found:440 variables
Found:45 variables
GDFS read all done, GDFS_35570401478243.BIN written
Phone detached
Elapsed:37 secs.
[ This Message was edited by: AlexRussell on 2011-10-29 16:57 ]
Posted by Lollylost100
What does it do when you try to start it? Screenblink white? Blinking red diode?
Posted by AlexRussell
It doesn't start at all, no signal, completely dead, it did blink the red diode because of the uncharged battery, but now not.
Posted by Boysie
You have a non standard EROM. Use Omnius to reflash R3A022.