Mitsumi usb bt & t68 & xntdconnect wont connect

Posted by make10
Hi!

I am currently strugling with the above combination.

What I am able to do is: Connect to the phone over BT with hyperterminal and give AT-commands, connect to the phone using ??flaw?? mobile agent.
It look's like any program that uses COM port "correctly" works...

Why is it so that when I try to use that sw. made by Ericsson I'll just get message phone not found... At the bottom of this post is short cut-n-paste from mobile phone monitor's debugger.

Phone is T68 upgraded to sw. R2E006, USB-BT is Mitsumi WIF-0402C (www.mitsumi.de), OS is W2k Pro. + SP2.

Anyone had similiar problems ??? Resolved???? Please help...

Debug out start------

(+317.704 s) 0x0658 CPortPoll (2) :Port \.ANUBCOM has status DISCONNECTED
(+317.704 s) 0x0658 CPortPoll (2) :PollComport \.ANUBCOM for arrive
(+317.704 s) 0x0658 CCOMMPortResourceCollection (2) :Lock \.ANUBCOM
(+317.704 s) 0x0658 CPortPoll (2) :PollForArrival of \.ANUBCOM
(+317.704 s) 0x0658 CPortPoll (2) :Poll \.ANUBCOM for arrival
(+317.704 s) 0x0658 CAB (2) :Entering _CAB_CreateFile
(+317.704 s) 0x0658 CAB (2) :_CAB_CreateFile - Reserved port, current port is INVALID_HANDLE_VALUE
(+317.705 s) 0x0658 CAB (0) :_CAB_CreateFile - Could not open port, INVALID_HANDLE_VALUE
(+317.705 s) 0x0658 CAB (2) :PollComport - CreateFile(\.ANUBCOM) API failure (0x2)
(+317.705 s) 0x0658 CPortPoll (2) :Poll PORT_STATUS_UNKNOWN
(+317.705 s) 0x0658 CPortPoll (2) :PollForArrival of \.ANUBCOM finished
(+317.705 s) 0x0658 CCOMMPortResourceCollection (2) :Unlock \.ANUBCOM
(+317.705 s) 0x0658 CPortPoll (2) :m_vPortPollInfo.Unlock()
(+318.265 s) 0x0644 MSIrSock (1) :getCurrentIrSocketDevices Getsockopt error: 10050 PROBABLY DISABLED
(+318.705 s) 0x0658 CPortPoll (2) :m_PhoneVisualiser.IsPolling(TRUE)
(+318.705 s) 0x0658 CPortPoll (2) :m_vPortPollInfo.Lock()
(+318.705 s) 0x0658 CPortPoll (2) :Port COM3 has status DISCONNECTED
(+318.705 s) 0x0658 CPortPoll (2) :PollComport COM3 for arrive
(+318.705 s) 0x0658 CCOMMPortResourceCollection (2) :Lock COM3
(+318.705 s) 0x0658 CPortPoll (2) :PollForArrival of COM3
(+318.706 s) 0x0658 CPortPoll (2) :Poll COM3 for arrival
(+318.706 s) 0x0658 CAB (2) :Entering _CAB_CreateFile
(+318.706 s) 0x0658 CAB (2) :_CAB_CreateFile - Open reserved port, but no change in mode
(+321.810 s) 0x0658 CAB (1) :_AsynchQueryPort - No modem status in 3000 ms.
(+321.810 s) 0x0658 CAB (2) :Entering _CAB_CloseHandle
(+321.810 s) 0x0658 CAB (2) :open port not really closed
(+321.810 s) 0x0658 CPortPoll (2) :Poll PORT_STATUS_UNCHANGED
(+321.810 s) 0x0658 CPortPoll (2) :PollForArrival of COM3 finished

[ This Message was edited by: make10 on 2002-08-12 07:36 ]

Posted by GOwin
check the virtual com port config in MPM settings

Posted by make10
already checked, only COM3 is enabled, it is also reserved(won't affect if it's not reserved).

Is there anyway to configure the timeout value and/or force MPM to monitor only COMx (currently it still check's that which port to monitor)... Crawled through registry but found nothing......

Posted by GOwin
the bluetooth adapters usually uses virtual com ports. is com 3 a virtual com port in your sytem?

if not, check your serial port settings in your bt configuration program

Posted by make10
Yes it is, as I already said I can connect to the phone over bt but MPM won't detect my phone...

Btw. in the commercial version of XNTD sw. there is possibility to set com-port and it's speed or select IR.... Too bad that, atleast trial version won't support T68...