Posted by amitn
I am having T230 handset and ERI T28 cable. When I connected my mobile to PC, mobile sends continuous data on PC (probably some settings) at 115200 baud and not responding to any AT command. I am using HyperTerminal software. I want to send sms by using AT commands only.
Help me.
How to stop these messages from T230? how to send it in AT command listening mode?
RLC: RLC_TIMER
RLC: RLC_TIMER_T3164 = 14430
RLC: RLC_TIMER_T3166 = 14431
RLC: RLC_TIMER_T3180 = 14432
RLC: RLC_TIMER_T3182 = 14433
RLC: RLC_TIMER_T3190 = 14434
RLC: RLC_TIMER_T3192 = 14437
RLC_UL: S I
RLC_DL: S I
LLC: PID 53
LLC:[lt][/lt]SMS 10867
LLC:[gt][/gt]SMS 10863
LLC:[lt][/lt]SNDCP 14330 14338
LLC 1: state 0
LLC 3: state 0
LLC 5: state 0
LLC 7: state 0
LLC 9: state 0
LLC 11: state 0
MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 260 bytes requested in total ****RLP: process started
RLP: state changed to `S0_ADMandDetached`
ConnHandler: process started
ConnHandler: state changed to `NoNetwork`
L2RCOP: process started
L2RCOP: state changed to `Initial`
DC state 0
PCM_OTD: Entering state PCM_OTD_STATE_IDLE.
POP3 started process id: 119
FIRST_POP3_REQ_SIGNAL: 18500
MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 279 bytes requested in total ****
MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 327 bytes requested in total ****
MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 467 bytes requested in total ****
MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 647 bytes requested in total ****
MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 797 bytes requested in total ****
MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 966 bytes requested in total ****
MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 1130 bytes requested in total ****
*** GLOBALD IS READY! ***
*** GLOBALD IS READY! ***
*** GLOBALD IS READY! ***
MMM state 0
MMM MM_SIM_DATA_SET_REQ
RR Multislot class GPRS = 4
RR state 0
CCS Err: Codec def
Request_HSCSD_NT_ConfigParameters_Set 2
** Before Read GD_TypeApproval_AudioTest **
** After Read GD_TypeApproval_AudioTest **
ETX OK
Reqs
uest_HSCSD_NT_ConfigParameters_Set 2
HW_EXTDSP: DSP Variant[0:None;1:ROM;2:RAM]:(1)
HW_EXTDSP: DSP ROM Type[0:Unknown;1:Anna1;2:Anna2]:(2)
MALL: **** NEW MAXIMUM XRAM HEAP USAGE: 1334 bytes requested in total ****
PH_INIT: Anna DSP Version 2/27/03 13:50:23
PH_INIT: Anna DSP Patch Version 11/12/03 16:10:38
PH_INIT: Ext DSP Initialize Complete - Sleeping
MPH: PacketChannels activated
MS_TYPE = MS_EGSM900_DCS1800
MPH_GD_Info.SensitivityLimit_dBm[BAND_GSM900_OR_EGSM900] = -107
MPH_GD_Info.SensitivityLimit_dBm[BAND_DCS1800] = -107
MPH_GD_Info.SensitivityLimit_dBm[BAND_PCS1900] = -107
MPH_GD_Info.MinNrOfIdentifiedCellsToSkipWeakCe lls = 0
Request_HSCSD_NT_ConfigParameters_Set 2
Request_HSCSD_NT_ConfigParameters_++
TL_Count er 12 CDT_Counter 15
MPH Serving
52 -75 30 34
MPH TopList
60 -86 19 23 72 = 4x 58
54 -89 16 20 72 = 4x 60
47 -90 15 19 72 = 4x 62
62 -90 15 19 72 = 4x 57
53 -91 x x 72
50 -92 x x 100
(51 -92 )
(61 -91 4x 59)
(57 -93 4x 61)
(55 -95 )
(56 -87 4x 61)
(59 -96 )
+++++
TL_Counter 12 CDT_Counter 15
MPH Serving
52 -75 30 34
MPH TopList
54 -88 17 21 97 = 4x 60
47 -90 15 19 97 = 4x 62
53 -91 x x 97
51 -92 x x 125
60 -92 13 17 97 = 4x 58
62 -92 13 17 97 = 4x 57
(50 -92 )
(57 -93 4x 61)
(61 -91 4x 59)
(55 -95 )
(59 -96 )
(49 -101 )
++++++
Posted by Qoastro
If you want to send sms from your comp you should check out FMA (Floats Mobile Agent).
Maybe it'll solve the problems.
//Qoastro
Posted by phuchqv
How can I use T610 cable to transfer data to T230 phone?
May I have to make any changes on T610 cable?
Posted by govigov
Nope. No changes are required.
Posted by phuchqv
I tried many times. PC recognize my t230 phone with t610 cable but I can't upload anything to phone. I use FMA but when I upload it says Obex is busy
[ This Message was edited by: phuchqv on 2005-03-22 01:56 ]
Posted by amitn
Anybody connected T230 handset with ERI T28 cable?