SEUS is upgrading to CID53. Be careful! || Jdflasher a solution

Posted by tranced
i know this has been discussed in others thread, but not as it should. this is important to know because if you try to upgrade your phone with SEUS it will probably upgrade it to CID53 and you will have wait till it be broken as CID 36/49/51/52 were broken.

we already have a victim > XS+ FSX prob K800

there is also a thread in se-nse about this: ATTENTION! CID53!, Be careful with SEUS!

for possible solutions:

Tutorial | General Usage - Jdflasher, Idiot proof!(SE-NSE)

Flash K800 CID53 with K810 software CID53 (for begginers)(ESATO)

_________________
i

jay0726||i

missing clara

||most helpful member, according masseur||telefonicos

[ This Message was edited by: tranced on 2008-06-04 10:58 ]

Posted by gaming_guy
i found this on se-nse

list of models upgraded to 53
K530c
K550i
K550iM
K610i
K618i
K770i
K790i
K800i
K810i
K818c
S500i
T650i
T658c
V630i
W580i
W610i
W660i
W710i
W830i
W850i
W880i
W888c
Z610i
Z710i

Posted by tranced
@gaming guy: thanks for the list. now knowing this you have to be more careful

p990 is not there

Posted by Muhammad-Oli
It looks to be just A100 phones, not UIQ

Posted by tranced
@oli: i know that's for non smartphones. that's why i put a

so can we say this is a strategy from

to stop modding their phones?

Posted by aremaboy
Just FYI, www.wotanserver.com has this CID 53 support already. In case you need to reflash the phone..

Posted by tranced
@aremaboy: we can just upgrade our phones with wotan? you know there are ppl who want to modify their phones rather than upgrade them.

Posted by YZF R1
Is there a risk of cid 53 in upgrading W810i?

[ This Message was edited by: Rahul15 on 2008-04-05 13:07 ]

Posted by tranced
the w810 is not in the list that gaming_guy posted before.

there are only cid49/50 for w810 afaik.

Posted by markztrance
how about the K750??

Posted by tranced
no, i dont think so. the k750 is an oldie.

Posted by markztrance
it means that it will only affect most DB2020 phones..?

Posted by whatsucka
ic how dis works... so how can i fix my dead CID36 w800?? will it b dead forever??

Posted by strizlow800
Well this CID53 upgrade is ment to stop the modding of our phones in my opinion... That was the same case with the CID36 in the past. The K750s were CID36 until the modding started. Then

started to manufacture then CID49... The W810 is the same case... CID49 and then CID50... So this is what is happening with the DB2020 series too... They had 3 CIDs in the beginning that were cracked (CID49, 51 and 52), so now

releases a new kind of "protection" named as CID53 so we cannot mod our phones... But don't worry it will be cracked very soon

(as usual) hahahaa

Posted by strizlow800
@whatsucka

about your dead CID36 W800... SEUS doesn't work with dead phones... It works only with fully functional working phones, just to update the firmware (and f*** up your CID

). Anyway your W800 can be repaired for sure if it is software problem. Have you tried flashing the MAIN and the FS... If not, a complete software flash can solve the issue for sure. It includes:

GDFS write (new gdfs)
flash EROM
flash MAIN
lash FS
customize...

But if the phone is not recognized by the PC when connected with DCU60 cable, you will need to look for service cable (cruiser works fine with CID36 W800s)...

Posted by whatsucka
where can i get the MAIN and the FS?? i've been looking everywhere still cant find it...

n about the service cable , wats da diff from it with regular DCU-60?? i juz try connecting my w800 to my laptop but it wont read it at all under setool n XS++ it was still working a few days ago even my fone was dead, i think mayb the fone even drain battery when is dead cuz da battery was 100% charged when i plug into SEUS

Posted by strizlow800
The difference between the regular DCU60 and the service cable is that the service cable can revive a dead phone, and make the pc recognize and flash it even if the pc does'nt recognize it. With other words, it alives the dead

Posted by strizlow800
If a service cable is needed it cam be made folowing this tutorial:

http://forums.se-nse.net/index.php?showtopic=3360

If you have issues with the pictures you can see them here:

http://semkd.19.forumer.com/viewtopic.php?t=19

but on semkd site the tutorial is on macedonian...

W800 R1BC002 CID36 firmware link:

http://rapidshare.com/files/105250224/W800_R1BC002_CID36_-_strizlow800.rar.html

_________________
Sony Ericsson Master strizlow800 - (Team SeMKD)

[ This Message was edited by: strizlow800 on 2008-04-06 09:11 ]

Posted by whatsucka
kool thanx so much!! i have to charge my fone in order to see y my pc wont see my fone

Posted by strizlow800
There might be several reasons why your PC does not recognize your phone... It may be:
- hardware damage
- fastport damage (broken connectors or cable)
- empty battery
- software damage (EROM and GDFS)...

The last 2 are 99% of your case... Anyway if it is the battery, the phone will be recognized after recharging the batt... (if not try with another one)...

If it is the "software damage" thing, (damaged EROM or GDFS) and the phone is not recognized by the PC, you will have to use service cable to reflash it's EROM and GDFS... The service cable uses 3+ volt battery (anyway I use 9V hahaha

) to revive the dead phone - put some electricity in it so the PC can flash it's EROM or GDFS and make it alive again

.

Hope you understood me:)

Posted by whatsucka
I understand da EROM n gdfs part but not the battery part

Posted by gaming_guy

On 2008-04-06 15:55:43, whatsucka wrote:
I understand da EROM n gdfs part but not the battery part

battery not having enough charge to power the phone

Posted by strizlow800
If battery is completely drained, it does not have the power needed to power on the phone or at least give it electricity to be recognized by the pc...

Posted by whatsucka
noooooooo i full charge my battery and my computer still cant read my w800... i think i really need to get a service cable... or i can make 1 since my major is networking so cabling should b piece of cake...hehe

i got so many SE fones but only using 1 DCU-60

Posted by strizlow800
Sorry to hear that.... After all, you can try to connect to setool, far manager or other programs to see if the phone is not totally dead (it just may work sometimes)... If not, you would have to flash it with service cable...

Posted by Soyish
I've the newest k810 firmware. R8BE001. But my cell is still cid52

Posted by strizlow800

On 2008-04-08 06:24:27, Soyish wrote:
I've the newest k810 firmware. R8BE001. But my cell is still cid52

Well if you updated through SEUS and you still have CID52, it may be result of your CDA... Not all CDAs are upgraded to CID53 yet...

Posted by vegetaleb
Lot of people are updating their K850 to the new 037 FW ,is it CID53?

Posted by glorfingal
got caught with my w610i ... now cid53. wotan may have cid53 support
but there's no cid53 firmware so no reflashing either

Posted by f a
i'm using w610 main and k550 main..

are there any news saying that this upgrade could make any phone support the MXE-60? since i really need a xenon flash..

Posted by kheopstr
k550i

i am using cid-52 r8ba024 c_asia but when i check it for new fm on seus nothing says new.

İ wanna make it cid 53

but i cant

is ther anyone which is using k550i with cid 53?

Posted by joseph0829
@kheopstr

stick to CID52, you might want to revert your phone, but wont allow you anymore

Posted by k series
anyone know when cid 53 will probably be cracked

Posted by nickless09
i received a new phone and it came with CID 53 god dammit!!!!!!
how can i revers it??

Posted by tranced

On 2008-05-01 19:03:51, nickless09 wrote:
i received a new phone and it came with CID 53 god dammit!!!!!!
how can i revers it??

afaik, anybody has been able to downgrade CID's but upgrade.

Posted by Killfr3nzy
so whats the problem with this cid 52?
can some one explain

and where can I check mine?

thanks

[ This Message was edited by: Killfr3nzy on 2008-05-01 18:31 ]

Posted by tranced
there isnt any problem with the CID52, the problem is with CID53.

you can check yours with xs++ v3.1 or any xs++ out there.

Posted by Killfr3nzy

On 2008-05-01 19:35:41, tranced wrote:
there isnt any problem with the CID52, the problem is with CID53.

you can check yours with xs++ v3.1 or any xs++ out there.

Sorry I mean, whats the problem with cid 53 then?

Posted by tranced
afaik, that xs++ doesnt support CID53 nor setool.

Posted by eddie2020
a noob question... how do i know that my phone is CID53 or what??

i m using k810 r8ba024

Posted by tranced
with xs++ or setool.

just connect your phone to either xs or setool and you'll see your CID

Posted by bryanjay420
@tranced

is CID53 really supported by jdflasher???i mean they told that you can vie FS using jdflasher...

Posted by bryanjay420
if you want to upgrade CID go to SEUS!

Posted by tranced
the OTP CID means the original CID it was, now is CID52.

Posted by eddie2020

On 2008-04-08 15:00:10, strizlow800 wrote:

On 2008-04-08 06:24:27, Soyish wrote:
I've the newest k810 firmware. R8BE001. But my cell is still cid52

Well if you updated through SEUS and you still have CID52, it may be result of your CDA... Not all CDAs are upgraded to CID53 yet...

lolx newest 810 firmware is R8BE001?? how about R8BA024? what difference?

Posted by k series
anyone know when or how to crack a cid 53

Posted by bryanjay420
CID53 is explorable using jdflasher latest plug-in...try

Posted by aem
how can i know if my phone is CID 53?

Posted by totalgsm

On 2008-05-09 05:24:58, aem wrote:
how can i know if my phone is CID 53?

Read info with software.