Withan™ Camera Driver V3/S3 Rev.1 for SE k790/k800/k810 phones

On 2008-01-25 23:17:53, toyds wrote:
i think this is the FF command

seq_set_prop_e_2 = $sb 04 // Forced ON, for service menu and production tests
$c9 08 // R5 camera version?
#COM_EVENT(5a,83) // Forced xenon 0b10000011, slow sync at beginning
$cl
#COM_EVENT(51,00) // Sensor scene "Auto 00"
#COM_EVENT(5a,8b) // FLASH_MODE 0b10001011: Flash on, RER off, sync on beginning.
$cx;

On 2008-01-26 17:29:49, reywal wrote:
the pictures are just too good to be true..

On 2008-01-26 19:11:25, jomateixa wrote:
I don't post edited pics you can trust me, if you want I could upload these in fullsize

On 2008-01-26 19:16:13, Goldmen wrote:
Amazing colours!!!
Verry good job!


...if you please...!?
Another one question:
Can we set manual saturation....?
...and how....?


[ This Message was edited by: Goldmen on 2008-01-26 18:24 ]

On 2008-01-26 19:32:45, milan91 wrote:
jomateixa, now i try 2.1 vivid and again problem...
When set document mode and EV -2.0 ISO is 320 , but when i take second picture ISO is 100 and that's normal...
Can anybody try 2.1 vivid or other jomateixa driver, i have k800i with k810i fs and main, R8BA024 version...

On 2008-01-26 19:57:38, Goldmen wrote:
@jomateixa
How we can reach ISO-80 and exposure time 1/1600...?
Thank you!


[ This Message was edited by: Goldmen on 2008-01-26 19:01 ]

On 2008-01-26 19:39:15, jomateixa wrote:

We were talking about that...but I don't know why do you have that problem. I tested a lot of times and NEVER happened to me. There's no secret in the code, DOC mode have ISO 100.

Can you post two pics for me to see clearly the problem? Thanks

On 2008-01-26 20:53:03, jomateixa wrote:

I don't have the mcb881 technical specs, if someone have please share

On 2008-01-26 21:50:23, yorulezkos wrote:
i did what you said... :
picture 1


picture 2



[ This Message was edited by: yorulezkos on 2008-01-26 20:50 ]

On 2008-01-26 22:19:25, milan91 wrote:
wtf?!?
And now problem is in my phone??
Can you post your product code?? Turn off phone, remove battery, and on phone there is code, like this 07W33...

On 2008-01-26 19:32:45, milan91 wrote:
jomateixa, now i try 2.1 vivid and again problem...
When set document mode and EV -2.0 ISO is 320 , but when i take second picture ISO is 100 and that's normal...
Can anybody try 2.1 vivid or other jomateixa driver, i have k800i with k810i fs and main, R8BA024 version...

On 2008-01-27 11:01:01, bizon69 wrote:
Can you make your newest driver 2.1 with 08 sharpness?

On 2008-01-27 11:01:01, bizon69 wrote:
@jomateixa

Can you make your newest driver 2.1 with 08 sharpness?

Thanx

_________________


[ This Message was edited by: bizon69 on 2008-01-27 10:01 ]

On 2008-01-27 22:55:19, BundyRRR wrote:
Thanks mate:) I do my best:)
Sometimes I set wrong white balance and photos are not colourfull enought, but it's only my fault. And I must say, that your driver is better than genus driver in difficult, indoor conditions. And the landscape mode is awesome, sharp and clean:)
Thanks:)


_________________
http://www.flickr.com/photos/12005930@N07/

[ This Message was edited by: BundyRRR on 2008-01-27 21:56 ]

[ This Message was edited by: BundyRRR on 2008-01-27 21:56 ]

On 2008-01-27 22:58:34, Goldmen wrote:
@jomateixa
What mean value "0b" of colour saturation in your Ultimate 2.1_vivid?
What is equivalent by digits?
Thank you!

[ This Message was edited by: Goldmen on 2008-01-27 22:02 ]

On 2008-01-27 23:46:42, jomateixa wrote:


Goldmen, a little learning:

- When you see '0x' before a value, for example 0x0C, it means that the digit after '0x' string is in basis 16, Hexadecimal. ('normal' numbers are in basis 10, because humans have 10 fingers)

- In Hex, digits from 0 to 9 have the same value as in decimal basis, and from ten to fifteen are:

A=10
B=11
C=12
D=13
E=14
F=15

If you want more info read a wiki!