Posted by SEKseries
On 2007-11-19 12:45:06, quangbh30 wrote:
i use twilight portrait on third pic
Your third picture is blur......
Posted by quangbh30
a bad focus
Posted by quangbh30
Twilight landscape
Normal
Twilight portrait
[ This Message was edited by: quangbh30 on 2007-11-19 12:04 ]
Posted by genus
Sure like that, even u use 2.5 driver, the wood furniture absorb light with wide wavelength, so this cause much noise because it is dark.
i didnt touch any about noise, in camdriver didnt have any that setting for reduce noise, the phone firmware were determine for it, you can try with 2.5 driver, it also worse, but because 2.5 jpeg compression much lower (90%), so it give less noise ( blur picture).
If this give worse noise, i think the other will much worse, because my sharpness alrdy set lower to 02 and jpeg compression 92%.
Anyway, we should consider the 90% default jpeg compression.
[ This Message was edited by: genus on 2007-11-19 15:40 ]
Posted by genus
On 2007-11-19 12:54:10, quangbh30 wrote:
a bad focus
For distance more than 1m, you can choose infinity focus mode, because at dark place, hard to focus.
I think we can set back the default jpeg compression 90% and try and see the result for the noise problem. But i think i just can help little, because the picture as you take, the chair and the table, this kind of thing will give much noise, i also got try many before.
[ This Message was edited by: genus on 2007-11-19 15:47 ]
Posted by TehKek
Who cares about noise? Just pick a longer shutter speed and reduce the ISO? Is the code for chaning the shutter speed already working? Because, quite frankly that is THE way to reduce noise.
Until we can get it working, use NeatImage, you can reduce most of the noise with that if not all of the noise with ISO's < 500
Posted by Guto_ViP
On 2007-11-19 16:50:43, TehKek wrote:
Who cares about noise? Just pick a longer shutter speed and reduce the ISO? Is the code for chaning the shutter speed already working? Because, quite frankly that is THE way to reduce noise.
Until we can get it working, use NeatImage, you can reduce most of the noise with that if not all of the noise with ISO's < 500
Noise Ninja is better!
Posted by burner8
Noise Ninja? Where can i get this tool?
@Genus: Geat work, i've told this before, but
I recognize, that your driver have really more noise as gprsman's driver.
I compared your driver with gprsmans driver and found out, that he activate the noise filter from night portraid mode for the normal-mode and the results indoor pics are great with no noise. You have to try it and fix it in your driver!
But your driver, genus take tbetter flash pics.
So i for myself, took gprsmans driver with fix contrast from 1 to O and take genus flash seittng into gprsmans driver and the result is great. Good outdoor and good indoor, without noise and now good flash pics.
Thank you genus and gprsman, for your work.
Posted by ahil13
@gprsman i use your 2.1 camdriver and photos with picture quality normal are better than fine! The pics sizes also. Try
Posted by Guto_ViP
On 2007-11-19 21:05:00, burner8 wrote:
Noise Ninja? Where can i get this tool?
Search the programa on google, i have the serial.
On 2007-11-19 21:05:00, burner8 wrote:
So i for myself, took gprsmans driver with fix contrast from 1 to O and take genus flash seittng into gprsmans driver and the result is great. Good outdoor and good indoor, without noise and now good flash pics.
Put your modificate camdrive one my server se4u.4shared.com, i want test it!
On 2007-11-19 21:46:33, ahil13 wrote:
@gprsman i use your 2.1 camdriver and photos with picture quality normal are better than fine! The pics sizes also. Try
Gprsman camdriver doesnt work Whitebalance, test this because for me not works., all pics have the same configuration (light, color, etc.).
Posted by burner8
ok guys, here is my first great camdriver (Ihope for you all too).
http://rapidshare.com/files/7[....]nd_great_genus_flash_.rar.html
It based on gprsman 2.1 without noise
contrast fix to original for better contrast
flash settings from genus new driver with 1/30 sec.
night settings improved for better noiseless night pics
Try it and post your results
Thanks genus and gprsman for your great work.
burner8
Posted by quangbh30
The link not work, can u post it again?
[ This Message was edited by: quangbh30 on 2007-11-19 22:57 ]
Posted by burner8
the link is working.
Posted by quangbh30
I can't open it, can't u use 4shared?
4.6 a little blue
[ This Message was edited by: quangbh30 on 2007-11-19 23:27 ]
Posted by burner8
here is another link:
http://www.4shared.com/accoun[....]ash_.html?sId=mvzOHFwQbhaAenBN
burner8 camdriver 2.1 based on gprsman2.1 with original contrast settings and great genus flash .rar
Posted by rockygali
hi guys! i just found this on another thread here...
hope paparazy wont mind...
On 2007-11-19 13:34:29, paparazy wrote:
// lembre valores em hexdecimal 00, 01, 02, 03, 04, 05, 06, 07, 08, 09, 0a, 0b, 0c, 0d, 0e, 0f, 10....
//************************************************
// Exposure property 0 *******(THis is the exposure setting taken from the W900)
//************************************************
// 0 => -3 EV, 1=> -(2 2/3) EV .... 15=> 2 EV
//---------------------------------------------------
seq_set_prop_0=$s0 %0 $-0 09 $b0 00 5 3 06 02 00 01 $w0 06 #CMD_END; // altere o 09 para 0a você diminui o ev (exposição) padrão
// Configuração Video k750
VR_NORMAL_MODE_FR=3C; // fps grav video normal
VR_NIGHT_MODE_FR=30; // fps grav video night
// Configurações iniciais k750
seq_init=
06 02 00 01 00 56 #CMD_END // fix PaParazy nivel do filtro bilinear
06 02 00 01 01 55 #CMD_END // fix paparazy contraste 1
06 02 00 01 32 57 #CMD_END // fix paparazy Hue 32
06 02 00 01 08 58 #CMD_END // fix paparazy saturação 08
05 02 00 20 fc #CMD_END // fix paparazy mudar verde para vermelho
05 02 00 21 e2 #CMD_END // fix paparazy mudar amarelo para azul
06 02 00 01 01 13 #CMD_END // fix paparazy aplicar alteração cores
// 06 02 00 01 01 08 #CMD_END // ligar spot (base de brilho ao centro)
#GET_SENSOR_VERSION;
// pre-shutter da foto só para tela
seq_set_prop_7_0=06 02 00 01 28 03 #CMD_END // Slowshutter locked at min 20 fps => 10 fps draft mode
05 02 00 08 3C #CMD_END // ((Altere 3C para 3f fica mais rapido))30fps => 15 fps, Normal mode
06 02 00 01 81 34 #CMD_END // Transition to draft mode, use each 2 frame
#WAIT_FOR_MODE_TRANSITION;
seq_set_prop_7_1=06 02 00 01 0a 03 #CMD_END // Slowshutter locked at 5 fps draft mode
05 02 00 08 1e #CMD_END // ((Altere 1e para 21 fica mais rapido))15fps, Dark mode
06 02 00 01 01 34 #CMD_END // Transition to draft mode, use every frame
#WAIT_FOR_MODE_TRANSITION;
// Shutter do video relação fps
LOCK_NORMAL_FPS= 05 02 00 08 40 #CMD_END // ALTERE AQUI o 40 para 32 fica mais lento
06 02 00 01 40 03 #CMD_END // ALTERE AQUI o 40 para 32 fica mais lento
06 02 00 01 81 34 #CMD_END
#WAIT_FOR_MODE_TRANSITION;
// Redução shutter para noite k750 isso faz redução do ruido anoite!
SM_NEW_ENHANCE_NIGHT_MODE= $p1 07
$c1 01
$p1 0d
$c1 00
//--------------------------------------------------------------------------------
$p1 0e //|
$c1 00 //|
05 01 00 23 01 $f $r2 1 1 //|
$m0 1 $/0 28 //|
$c0 00 //|
$m0 1 $/0 03 //|
$c0 00 //|
$cl //|>--- ENM
$s0 40 $-0 r1 //|
06 02 00 01 04 51 $f $d0005 //|
06 02 00 01 $w0 04 $f $d0005 //|
$cx //|
$cx //|
$cx //|
//--------------------------------------------------------------------------------
$cl
//--------------------------------------------------------------------------------
05 01 00 23 01 $f $r2 1 1 //|
$m0 1 $/0 28 //|
$c0 00 //|
$m0 1 $/0 03 //|
$c0 00 //|
$cl //|>--- LED ENM
$s0 3d $-0 r1 //|
06 02 00 01 04 51 #CMD_END //|
06 02 00 01 $w0 04 #CMD_END //|
$cx //|
$cx //|
//--------------------------------------------------------------------------------
$cx
$cx;
seq_ss_take= $c7 00 // If take flag is zero...
$s7 01 // ...then set take flag to one and perform the code below
#EMPTY_EVENT_FIFO $z0 $-0 re $c0 00 $cl //Don't do anything if we already have the right size (for burst mode)
$p0 0d $c0 01 $p0 01 $c0 00 #LED_WB_SET $cx $cx #SM_NEW_ENHANCE_NIGHT_MODE 06 02 00 01 01 $ze
$ce 09 33 $cl 32 $cx $f #WAIT_FOR_MODE_TRANSITION #WAIT_FOR_CAPT_START $cx $t0020
// Ajuda avançada
#######HELP table i2c_commands advanced ##########
IMPORTANT:
------------------------------------------------------------------------------
This commands only for K750/W800/W810 phones!!!
In another phones - another commands and registers!!!
For more information visit:
http://www.sony-ericsson.ru/forums2/index.php or http://www.senews.ru/forum/index.php
------------------------------------------------------------------------------
Compiled by Andeo
------------------------------------------------------------------------------
***REGISTER DEFINITIONS***
**************************
------------------------------------------------------------------------------
Internal register 0,1,2,3 Used as temporary storage only
Internal register a Used to select EXIF parameter to read
Internal register e Used to remember last size id for snapshot burst mode
Internal register f Used to store property value
------------------------------------------------------------------------------
***COMMENTS***
**************
------------------------------------------------------------------------------
//COMMENTS COMMENTS - any your comments
------------------------------------------------------------------------------
***MACROS***
************
------------------------------------------------------------------------------
#MACROS PERFORM a macros. "MACROS" is any name of your macros. Place your macros at the beginning.
------------------------------------------------------------------------------
***COMPATION***
***************
------------------------------------------------------------------------------
$cX YY Check IF value of register "X" equal value "YY" THEN do next commands
.....
$cl ELSE do next commands
.....
$cx END IF (for $cX command)
------------------------------------------------------------------------------
***BASIC COMMANDS***
********************
------------------------------------------------------------------------------
$sX YY SET property "X" value "YY" for example:
$s5 40 PLACE value "64" in reg "5"
------------------------------------------------------------------------------
$sX %0 PLACE value in reg "X"
------------------------------------------------------------------------------
$mX YY COPY reg "YY" into reg "X"
------------------------------------------------------------------------------
$dXXXX WAIT(delay) for "XXXX" time in Hex (for example $d0100=Wait for 256 ms)
------------------------------------------------------------------------------
$wX WRITE the byte stored in register 0x0X (or simple reg "X") to the I2C bus
------------------------------------------------------------------------------
$rX READ the byte stored in register 0x0X (or simple reg "X") from the I2C bus
------------------------------------------------------------------------------
$bX OPERATE on register 0x0X (or simple reg "X")
------------------------------------------------------------------------------
$zX SET register "X" to last set size config
------------------------------------------------------------------------------
$pX YY SET register "X" to current value of property "YY"
------------------------------------------------------------------------------
$uXX UPDATE property "XX"
------------------------------------------------------------------------------
!0, !1, !2... TAKE A PARAMETER (one, two or three) holding the data to be written
------------------------------------------------------------------------------
$b3 YY Z 1 WRITE 0xYY (or simple "YY") to the "Z-th" bit in internal register 3. For example:
$b3 01 5 1 WRITE 0x01 to the fifth bit in internal register 3
------------------------------------------------------------------------------
$b2 XX Y 1 WRITE "Y" to bit "0" in register "2"
$b2 00 3 1 WRITE "3" to bit "0"
------------------------------------------------------------------------------
***ARITHMETIC***
****************
------------------------------------------------------------------------------
$
$>X 1 SHIFT the bits in register 0x0X (or simple reg "X") 1 bit to the right
------------------------------------------------------------------------------
$*X YY MULTIPLY reg "X" by "YY"
$*X rY MULTIPLY reg "X" by reg "Y"
------------------------------------------------------------------------------
$/X YY DIVIDE reg "X" with "YY"
$/X rY DIVIDE reg "X" with reg "Y"
------------------------------------------------------------------------------
$-X YY SUBSTRACT "YY" from reg "X"
$-X rY SUBSTRACT reg "Y" from reg "X"
------------------------------------------------------------------------------
$+X YY ADD "YY" to reg "X"
$+X rY ADD reg "Y" to reg "X"
-------------------------------------------------------------
[ This Message was edited by: paparazy on 2007-11-19 15:23 ]
hope you find something there...
Posted by toyds
@burner8 :
can you post sample picture taken using your cam driver?
thanks a lot
Posted by genus
On 2007-11-20 00:25:15, quangbh30 wrote:
I can't open it, can't u use 4shared?
4.6 a little blue
[ This Message was edited by: quangbh30 on 2007-11-19 23:27 ]
use cloudy WB, there is nothing to do with WB, camdriver cannot change the Wb range, it alrdy preset. This is because i increase the color ( decrease exposure), so the blue color looks more than normal.
Even 2.5 also, the WB at the time about 7-8pm, it will seem blue color, so we need to use cloudy, because the auto WB range is not large, & i cant change this...got nothing to do...
@tehkek
I alrdy try before, reduce the iso sometime also not reduce the noise too, but the noise will only reduce when the picture is more exposure ( overexposure). I alway use neoimaging reduce the noise, it is easy and simple, just one click
some more picture
[ This Message was edited by: genus on 2007-11-20 02:25 ]
Posted by reywal
Burner8, whats the video fps of your camera?
Posted by zhinjho
nice driver @Burner8...
Posted by number1
on genus 4.6
//************************************************
// Exposure property 0 *****
//************************************************
// 3 => -2 EV, 9 => -(0) EV .... f => 2 EV
//---------------------------------------------------
seq_set_prop_0 = $s5 %0
$-5 0a <<< causing the noise with this under flash #COM_EVENT(06,01) // Increase exposure to 1
#COM_EVENT(06,$w5);
//************************************************
// White balance, property 1 *******
//************************************************
// 0 => auto 1 => tungsten 2 => fluorescent
// 3 => clear sky 4 => cloudy
// 5 => one push 6 => hold
// 7 => Xenon 8 => LED
//---------------------------------------------------
seq_set_prop_1_0 = #COM_EVENT(11,00);
seq_set_prop_1_1 = #COM_EVENT(11,03);
seq_set_prop_1_2 = #COM_EVENT(11,04);
seq_set_prop_1_3 = #COM_EVENT(11,05);
seq_set_prop_1_4 = #COM_EVENT(11,06);
seq_set_prop_1_5 = #COM_EVENT(11,03);
seq_set_prop_1_6 = #COM_EVENT(11,03);
seq_set_prop_1_7 = #COM_EVENT(11,03);
seq_set_prop_1_8 = #COM_EVENT(11,03); this causes the blue pictures
Posted by Guto_ViP
Genus, your camdrive 4.6 doesnt work WB for me... i tested many times but not works.... Can you repair this?
Posted by number1
possible way to run different exposure in high and low light
$cc 00 // Normal
#COM_EVENT(06,03) // reset exposure <<< low-light exposure
$cl
#COM_EVENT(06,00) // reset exposure <<<< normal light exposure
$cx;
i havn't tested it yet it goes under Scenes, property 16, under $"Normal_scene"
Posted by burner8
Ok, here are some pics from my driver:
Posted by Guto_ViP
Burner8, Genus, Gprsman, why yours camdriver doesnt change color light when change WB?
Now WB Cloudy not have "brown light", all WB have the same light color on display.
Burner8, your camdriver makes a little lines (like this |_|) on upper side of display
_________________
K800 Silver R8BA024: Acoustic modd v1 R8(K800) by Peter / Camdriver 4.6B by Genus / Custom Menu Killer Bunny (BR by me) / Custom Right Button / Calibri Font by me / Custom Layout / Display v3 by Centus / Custom Splash/Logout/Startup
goto: se4u.4share.
[ This Message was edited by: Guto_ViP on 2007-11-20 18:38 ]
Posted by gprsman
@ burner8
very well
very good pics [ This Message was edited by: gprsman on 2007-11-20 18:49 ]
Posted by burner8
i see no lines, sorry.
@gprsman: thank you
[ This Message was edited by: burner8 on 2007-11-20 18:52 ]
Posted by Guto_ViP
Burner8, Genus, Gprsman, why yours camdriver doesnt change color light when change WB?
Now WB Cloudy not have "brown light", all WB have the same light color on display.
Burner8, your camdriver makes a little lines (like this |_|) on upper side of display
Somes pictures with Burner8:
Normal, WB Automatic
Normal, WB Fluorescent
Posted by Guto_ViP
On 2007-11-20 19:50:58, burner8 wrote:
i see no lines, sorry.
[ This Message was edited by: burner8 on 2007-11-20 18:52 ]
Hmmmm... very strange... on my display i see |_| on upper side when i will take the picture...
I will reinstall the camdrive, maybe it go out.
EDIT: Dammit.... isnt the camdrive.... I dunno what do this.... maybe layout? On focus for shutter this lines dissappier.
_________________
K800 Silver R8BA024: Acoustic modd v1 R8(K800) by Peter / Camdriver 4.6B by Genus / Custom Menu Killer Bunny (BR by me) / Custom Right Button / Calibri Font by me / Custom Layout / Display v3 by Centus / Custom Splash/Logout/Startup
goto: se4u.4share.
[ This Message was edited by: Guto_ViP on 2007-11-20 20:02 ]
Posted by quangbh30
i think it's not good. noise, sharpness no good
Posted by burner8
Some pics with my driver with flash @low light indoor normal mode:
Edit:
The yellow color is normal real colour.
Here another flash pic indoor without lamp @dark:
[ This Message was edited by: burner8 on 2007-11-20 23:08 ]
[ This Message was edited by: burner8 on 2007-11-20 23:09 ]
[ This Message was edited by: burner8 on 2007-11-20 23:13 ]
Posted by quangbh30
i think genus' cam is more sharpness and good contrast
Posted by quangbh30
i think k750i modded is better k8, sometimes pics taken by k750 is very good colour, sharpness, contrast
[ This Message was edited by: quangbh30 on 2007-11-20 23:41 ]
Posted by genus
On 2007-11-20 19:37:17, Guto_ViP wrote:
Burner8, Genus, Gprsman, why yours camdriver doesnt change color light when change WB?
Now WB Cloudy not have "brown light", all WB have the same light color on display.
Burner8, your camdriver makes a little lines (like this |_|) on upper side of display
_________________
K800 Silver R8BA024: Acoustic modd v1 R8(K800) by Peter / Camdriver 4.6B by Genus / Custom Menu Killer Bunny (BR by me) / Custom Right Button / Calibri Font by me / Custom Layout / Display v3 by Centus / Custom Splash/Logout/Startup
goto: se4u.4share.
[ This Message was edited by: Guto_ViP on 2007-11-20 18:38 ]
At low light condition, when you change the WB, it doesnt as in 2.5 driver, but when the light enough you can change it. I alrdy say i didnt touch on this, this is same as default 2.5 driver, until now i still cant solve this...
Posted by genus
@number1
Thx for the advice, we should increase the exposure and brightness when exposure property 0a, i will soon out the 4.6 full or 4.7. But i didnt see much noise....maybe is the sharpness and compression setting, i found that default compression 90% is much better, very less noise.
About the WB problem... did you hv anyway to fix it?
@Burner8
Nice picture!!!
[ This Message was edited by: genus on 2007-11-21 03:23 ]
Posted by quangbh30
4.6
Posted by number1
heres some advice for people modding the camdrivers, less sharpness = more clearness
Posted by salambaba
I bought this phone , can any1 help me to find good camdriver ?
Wich driver is best for K800i ?
(please with download link)
Posted by milan91
original driver is best
Posted by kuratinja
yo..kopritis ?? where's your new driver ?? everybody have a new one now...
Posted by xan K
On 2007-11-21 18:19:26, kuratinja wrote:
yo..kopritis ?? where's your new driver ?? everybody have a new one now...
In version 3.71's notes, on the first post, it kinda reads: "Last Mod", so....
Posted by tranced
i've tested that driver and the viewfinder is fast. i tried it on nightmode and it looked fine.
Posted by salambaba
No any1 have any idea about best moded camdrive ?
Posted by Guto_ViP
On 2007-11-21 21:15:08, salambaba wrote:
No any1 have any idea about best moded camdrive ?
Burner8 camdrive is good! wait for a new version of Number1's camdrive!
Posted by salambaba
where can i download it ?
Posted by G-Izzat
On 2007-11-21 21:37:19, salambaba wrote:
where can i download it ?
Burner8's camdrive.
http://www.4shared.com/accoun[....]ash_.html?sId=mvzOHFwQbhaAenBN
Posted by quangbh30
Burner's Cam
[ This Message was edited by: quangbh30 on 2007-11-21 23:00 ]
Posted by burner8
On 2007-11-21 03:38:19, genus wrote:
@Burner8
Nice picture!!!
Thank very much!
On 2007-11-21 21:32:17, Guto_ViP wrote:
Burner8 camdrive is good! wait for a new version of Number1's camdrive!
Thanks
@quangbh30: Nice pics with low noise.
It confirms the quality of the driver for me, and i hope for you too.
Indoor pics causes the largest challenge for the cam.
[ This Message was edited by: burner8 on 2007-11-21 23:25 ]
Posted by quangbh30
i will test it in the morning
Posted by xan K
well, the buzz is on. I'll give them a try.